PLUMBING ESSENTIALS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Blog Article

Details Here

Presented here down the page you can discover lots of professional ideas about How to Install a Bathtub.


How to Install a Bathtub
Installing a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old tub is easily accessible, the task can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to leave the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the task and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to consider utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This post will assist you set up a new tub in your washroom if you have currently acquired a brand-new tub and also don't require to transform the arrangement of your previous water supply pipelines.
Your tools and material checklist must make up the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited access that is commonly the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
    Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in area in between the tap and also the sink. Secure the tap in position with the maker given backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be linked to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Mounting the Tub


    Using both wood boards under its feet, position the tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the tub up until the level reads level.
    To set up faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
    Switch on the water and inspect all joints as well as brand-new pipework for leakages and also tighten them if needed. Load the bath tub and additionally inspect the overflow electrical outlet and the normal outlet for leaks.
    Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait up until the tub has actually been made use of at the very least once as this will resolve it right into its final position.

    Preparing for the Setup


    To start with, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to stop strain on the bathtub.
    Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its final setting.

    Tiling Around the Tub


    In the location where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, causing complications with moisture and possible leakages to the ceiling listed below.
    You can choose from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not think about this motion prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or waterproof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    We had been shown that report about Installing A Bathtub through an acquaintance on another site. Loved our write-up? Please share it. Help another person find it. I thank you for reading our article about How to Install a Bathtub.


    Order Repair

    Report this page